
800-829-0225

THE FILTER 1 ADVANTAGE
Dust Collectors
Downdraft Work Tables
Environmental Control Booths
or Call Us Today at 800-829-0225
Back to Top
HYDROTRON wet dust collector systems are specifically designed for safe collection of potentially explosive and volatile materials and are effective in the capture of fine metal particles. They meet the National Fire Protection Association (NFPA) guidelines for processing and finishing aluminum. Since the Hydrotron also meets OSHA and NFPA regulations for dust removal located inside buildings, it can recirculate in-plant, tempered air to conserve energy.
HYDROTRON Water Filter Dust Collectors by FILTER 1 purify air by a combination of centrifugal force and violent mixing of water and contaminated air. As the air stream passes the fixed baffles, particulate is separated by heavy, turbulent curtain of water created by high velocity air. The centrifugal force caused by the rapid changes in airflow direction forces the dust particles to penetrate the water droplets and become entrapped. Contaminated water is then removed from the airstream by special mist filters. Dust, as sludge, settles to the collector bottom and the water is reused.
APPLICATIONS
- Removes Respirable Dust and Contaminates from Sanding, Grinding, Deburring, Polishing, Packaging, and Processing
- Aircraft Maintenance, Repair, and Overhaul Operations
- Electrical, Communication, and Lighting Enclosure Manufacturers
- U.S. Military Operations
- Milling, Refining, and Ceramics Foundries
- Chemicals, Rubber Products, and Plastics
FEATURES
- TEFC Motors, Single and Three Phase
- Direct Drive/Non-overloading Fan
- Interior Baffle Section
- Special Mist Filters
- Low Maintenance
- Electronic Water Level Control
- Galvanized Steel Construction with Two-Part Cold Tar Epoxy Coatings to all Interior Wet Surfaces
- Industrial Enamel "Gulf Blue" Coating on Exterior
- Magnahelic Gauge.
AUTOMATIC FILL SYSTEM
- TEFC Motors, Single and Three Phase
- Direct Drive/Non-overloading Fan
- Interior Baffle Section
- Special Mist Filters
- Low Maintenance
- Electronic Water Level Control
- Galvanized Steel Construction with Two-Part Cold Tar Epoxy Coatings to all Interior Wet Surfaces
- Industrial Enamel "Gulf Blue" Coating on Exterior
- Magnahelic Gauge.

or Call Us Today at 800-829-0225
Back to Top
............HYDROTRON HWF SERIES DUCTED WET TYPE DUST COLLECTOR.............................
The HWF series is a safe and economic method of cleaning these potentially volatile materials. With air volumes between 500 CFM and 5,000 CFM, the units can be connected via ductwork to the dust generating machines for source capture.
MODEL
|
CFM
|
BLOWER H.P.
|
DIMENSIONS
|
WATER |
||
HEIGHT
|
WIDTH
|
LENGTH
|
||||
HWF1-10-3 |
1000 @ 4"
|
3 |
95" |
34" |
40" |
50 |

or Call Us Today at 800-829-0225
Back to Top
.......HYDROTRON DHYD SERIES WET TYPE DUST COLLECTOR / DOWNDRAFT TABLE................
The FILTER 1 HYDROTRON Downdraft Table is a self-contained workstation with its own water dust collection system, excellent for "cell manufacturing." It features easy installation and comes ready to run. The workstation is available with a single work surface or with two work surfaces, one on each side.
MODEL
|
CFM
|
BLOWER H.P.
|
|
DHYD2-30-5-4 |
3,000 |
5 |
2 Tables 30" X 48" |
The HYDROTRON gets the dust immediately wetted, reducing the risk of fire in ductwork and meets OSHA and NFPA regulations for dust collectors located inside the building. The standard unit includes a fiberglass grated work surface, a Regain Air Curtain in front to prevent dust from escaping the work zone, and a clear inspection door.
|
MODEL |
CFM |
BLOWER H.P. |
|
|
DHYD1-30-5-4 |
3,000 |
5 |
1 Table 30" X 48" |
or Call Us Today at 800-829-0225
Back to Top
........HYDROTRON HPB SERIES WET TYPE ENVIROnMENTAL CONTROL BOOTH.....................
The FILTER 1 HYDROTRON Control Booth, integrating the booth enclosure and wet dust collection, is a safe and economic method of cleaning potentially volatile materials. The HYDROTON HPBs are generally used for working on large objects that won't fit on a table, or for multiple table top operations where several operators will be in the booth at the same time. These wet dust collection booths meet OSHA and NFPA guidelines for dust collectors located inside the building, allowing recirculation of in-plant, tempered air to conserve energy. The units remove heavy sparks from grinding and gouging, and filter repirable dust and contaminates from sanding, deburring, buffing, packaging, and processing. The HPB series features a minimum of 300 FPM in the work zone, sound attenuating interior surfaces, and flourescent lighting with dust tight lens. The booths may be equipped with the Regain Air, "Push/Pull" technology pioneered by FILTER 1 to increase capture velocity,up to 800 FPM in the "breathing zone."
|
MODEL |
CFM |
BLOWER H.P. |
DIMENSIONS | ||
|
HEIGHT |
WIDTH |
LENGTH | |||
|
HPB6-1-1X10 |
5,500 |
10 |
7.5' |
6' |
154" |

or Call Us Today at 800-829-0225
Back to Top
